What are the common troubleshooting methods for tripod turnstiles and swing turnstiles?

What are the common troubleshooting methods for tripod turnstiles and swing turnstiles?

As the fast-track gates commonly used by the public, the stability and safety of the operation of the three-roller gate and the swing gate are related to the safety of life and property of the majority of users. It also has higher requirements for the safety of the public equipment we use, such as the three-roller gate and the swing gate.

Turnstile gate |Flap turnstile |Outdoor turnstiles|Outdoor turnstile |Turnstile technology | Flap barrier gate |Revolving gate|Flap barrier | Turnstile suppliers

Puerta de torniquete | Torniquete de aleta | Torniquete de exterior | Torniquete de exterior | Tecnología de torniquetes | Puerta de barrera de aleta | Puerta giratoria | Barrera de aleta | Proveedores de torniquetes

One: What should I do if the three-roller gate and the swing gate cannot open the gate after swiping the card or checking the ticket?

1. The pedestrian may have held up the rotating rod when swiping the card or checking the ticket. Please take a step back and swipe the card.

2. Please check whether the electromagnet is normal. If the control part has an output of the electromagnet voltage and the voltage is normal, but the electromagnet cannot be sucked up, then replace the electromagnet.

2. How to deal with the situation that several people can pass through continuously after swiping the card or checking the ticket at the three-roller gate?

1. Check whether the inductive screws on the proximity switch and the proximity switch bracket are loose. Under normal circumstances, when people pass through normally, the inductive screws will contact the inductive proximity switch, and the inductive light on the inductive proximity switch will light up. If the light is not on, use a multimeter to measure whether the input power of the proximity switch is normal. If it is normal, the proximity switch needs to be replaced.

2. When the proximity switch is confirmed to be not broken, check whether the electromagnet is reset when reading the card. If not, remove the electromagnet and check whether there is any foreign matter inside the electromagnet and deal with it. If there is no foreign matter, the spring strength inside the electromagnet can be increased, but not excessively. Too much will cause the electromagnet to fail to attract.

3. How to deal with the situation that the three-roller gate does not respond when swiping the card?

1. Check whether the ticket used is the ticket of this system and whether the ticket checking method is correct.
2. Check whether the connection of the card reader is normal. If it is a barcode ticket, please check whether the card is inserted in reverse, check whether the connection of the card reader unit is normal, and whether the angle of the barcode reader is accurate.

3. Check whether the button trigger board is normal.

IV. What should I do if the three-roller gate has a slow response speed when swiping the ID card?

1. The parameter setting is wrong. The problem is solved after correct setting

How to deal with the turning rod failure during the operation of the three-roller gate and the swing gate

I. What should I do if the turning rod of the three-roller gate and the swing gate cannot be lifted after power is turned on?

1. Press the turning rod down to the bottom and then lift it up.

2. Open the gate cover and check whether the retaining spring on the drop rod electromagnet device has fallen off. When the turning rod is pressed to the bottom, the retaining spring is in close contact with the electromagnet. If not, the electromagnet installation position needs to be readjusted.

3. Check whether the electromagnet is damaged. Use a multimeter to measure whether there is a supply voltage (24V). If there is voltage, the above checks are all correct. Please replace the electromagnet; if there is no voltage, please check whether the output part of the control drive board is normal.

2. What should I do if some three-roller turnstiles drop their bars when passing people?

1. The position of the drop-bar electromagnet is not installed properly, install it in the correct way.

2. Power supply problem, insufficient voltage, repair the circuit to ensure normal voltage.

3. What should I do if the gate machine does not drop the bars when it is powered off?

1. Check whether the installation position of the electromagnet is correct. The spring force of the drop-bar electromagnet bracket is too small, and adjust it in time.

2. The friction between the turntable and the turnbar is too large. During normal maintenance, maintenance should be carried out according to the maintenance guide.

Methods for handling turntable failures during the operation of three-roller turnstiles and swing gates

1. What should I do if the turntable of the three-roller turnstile can sometimes reverse?

Under normal circumstances, you can only enter after checking a valid ticket, and you cannot reverse. If reversal occurs:

1. Check whether the car stop pin is reset. First open the gate cover, add some lubricating oil to the car stop pin, and then pull the car stop pin back and forth to fully lubricate it. You can also remove the car stop bracket, take out the car stop pin, use a file to clean the burrs, then assemble it back, add liquid lubricating oil, and pull the car stop pin back and forth to make it completely movable.

2. It may be that the performance of the buffer is unstable, causing the turntable to be unable to reset. You can adjust the strength of the buffer or replace the buffer.

3. The position of the proximity switch is incorrect, causing the turntable to be unable to reset, so you need to adjust the position of the proximity switch.

2. How to deal with the up and down swing of the gate turntable?

1. The tray of the gate movement turntable is loose, and the gap between the fit is too large. Adjust the gap.

2. The screws of the gate tray are loose, tighten the screws in time.

Shenzhen Chuangxintong Technology Co., Ltd. specializes in the production of security gates, three-roller gates, swing gates, wing gates, full-height turnstiles and other channel products, and constantly innovates to create the greatest value for customers.